What are the details that need to be paid attention to when installing fully automatic reverse osmosis pure water equipment?
What are the details that need to be paid attention to when installing fully automatic reverse osmosis pure water equipment? Author: automatic reverse osmosis water equipment is now one of the commonly used water treatment equipment, bring a lot of benefits and convenience for the production of industrial, but the automatic reverse osmosis water equipment during installation details need to pay attention what? The automatic reverse osmosis pure water equipment should be as close as possible to the drainage place. If other water treatment facilities are needed, it should be considered to reserve an installation location. Do not install the fully automatic reverse osmosis pure water equipment within 3 meters of the tap water inlet, otherwise the water will flow back into the fully automatic reverse osmosis pure water equipment and damage the equipment. Place the device in an environment where the room temperature is lower than 1°c and higher than 49°c. Keep away from acidic substances and sour gas environment. Secondly, the connection of the pipeline of the automatic reverse osmosis pure water equipment should be in accordance with the standard construction of the pure water equipment installation and connected to the inlet and outlet pipes according to the control caliber. The inlet and outlet pipes should be equipped with manual valves, and a bypass valve should be installed between the outlet pipes. One is to facilitate the discharge of residues from the installation and welding process to avoid contamination of the resin; the other is to facilitate maintenance. A sampling valve should be installed at the water outlet, and a Y-type filter is recommended for the water inlet pipe. Try to shorten the length of the drain pipe (<6 meters), and not install various valves, and only use PTFE tape to seal during the installation process. A space must be maintained between the drain pipe and the water surface of the drain to avoid siphoning. Separate brackets must be set between each pipeline, and the gravity and stress of the pipeline are not allowed to be transmitted to the control valve. Installation requirements for fully automatic reverse osmosis pure water equipment: All electrical connections must comply with electrical construction specifications. Confirm that the electrical parameters of the controller are consistent with the power supply. There are independent power outlets. The installation of the water distributor and the center tube uses pvc glue to bond the center tube and the water distributor seat together. Insert the bonded center tube into the resin tank. Tighten the branch pipe of the water distributor on the water distributor seat. After the installation of the water distributor is completed, the center pipe should be vertically placed in the center of the exchange tank, and then the pvc pipe above the surface of the tank mouth should be cut off. Place the resin tank in the selected location. The center tube and the lower water distributor are firmly bonded with glue. The lower water distributor is facing downwards and the center tube is inserted into the resin tank of the automatic reverse osmosis pure water equipment. The height of the center tube and the height of the lower distributor should be level with the mouth of the tank. Qi. Cut off the excess part of the center tube. Note that the upper mouth of the center tube should be smooth and free of burrs. Take out the center tube. The resin is added to the resin tank and cannot be filled up. The space left is the backwash space of the resin, and the height is about 40%-60% of the height of the resin layer. Set the water distributor on the core pipe, or fix the water distributor on the bottom of the control valve first. Note that no matter where the water distributor is placed, it should be ensured that it will not fall and cause the resin to escape. Insert the core tube into the bottom of the control valve. The core tube must pass through the o-ring inside, and be smeared with water-insoluble lubricant before screwing into the valve to avoid damaging the sealing ring. Fix the water distributor on the multi-way valve.
Contact Person: Ms.Carrie Chan
TEL : (+86)020-39185731
E-MAIL : firstname.lastname@example.org
Whatsapp/Wechat : +86-13751887537
Water Treatment System Add:9A,Building 8,Lianfa Industrial Park , Luopu Street, Panyu District, Guangzhou City, China
Water Filter Cartridge Add:Zhangcun village,Daze town, Xinhui district, Jiangmen City, Guangdong, China
Sign up for our newsletter
Get the latest news and updates from the leaders in water treatment and process separation.